Quick Answer
- Fitment. 2010–2024 Ram 2500/3500 pickups with the 6.7L Cummins. Chassis Cab trucks need a separate guide.
- Install time. About 1–4 hours.
- Prep. Match the kit to your truck, gather your tools and coolant, and let the engine cool. Follow Ram’s battery disconnect and coolant drain procedures.
- Steps. Where lawful, remove the EGR tube, valve, and cooler. Fit the plates and hose, then refill, bleed, and check for leaks.
You’ve got the hood up and the kit on the bench. Then you notice the hose in your box has a different bend from the one in the video. That’s a good time to look up the part number. Once you know which kit you have, it’s easier to tell whether you’re looking at the right truck and the right set of instructions.
If a check-engine light or a dropping coolant level brought you here, write down the code and keep track of how often you’ve had to top off the coolant. Those two details give you a place to start looking for the fault.
U.S. emissions notice. Federal law prohibits tampering with emissions controls on EPA-certified vehicles. Off-road or racing use alone does not create an exemption. For an EGR fault on a certified pickup, have the factory system diagnosed and repaired. See EPA guidance on emissions tampering.
Find the guide for your Ram pickup
If you’ve got a 3500 dually or a flatbed, use the VIN to look up how your truck left the factory. A pickup can come with dual rear wheels or get a flatbed later. A factory Chassis Cab needs its own instructions. That includes the Ram 3500 Chassis Cab and the 4500 and 5500.
| Model year | Ram 2500/3500 pickup guide |
|---|---|
| 2010–2012 | 2010–2012 Ram EGR install guide |
| 2013–2018 | 2013–2018 Ram EGR install guide |
| 2019–2024 | 2019+ Ram EGR install guide. Check your model year against your kit’s fitment. |
If the box label is gone, look up the 6.7L Cummins EGR kits by year and compare the parts photos with what you have. If you’re still unsure, send SPEtuner a photo of the hardware along with your model year and factory body type.
Find your kit by model year
If you drive a 2010–2012 Ram 2500 or 3500 pickup, see the 2010–2012 Cummins EGR delete kit for the available kit options.
[[product-recommend:1]]
For a 2013–2018 Ram 2500 or 3500 pickup, check the 2013–2018 Cummins EGR delete kit for the parts included with each option.
[[product-recommend:2]]
Have a 2019–2024 Ram 2500 or 3500 pickup? Use the 2019–2024 Cummins EGR delete kit to check fitment for your model year.
[[product-recommend:3]]
Lay out the parts before you start
The kit manual is labeled 2010+. Match the parts on page 2 to your kit and confirm fitment for your truck before using the photos below. The manual shows a front and rear stainless plate, an intake-side plate, seals, a molded hose, a barbed fitting, and a standpipe adapter with its bracket hardware.
Tools and Preparation
Tools You’ll Need
- Metric sockets and wrenches. The manual calls out 8 mm, 10 mm, 14 mm, and 15 mm factory fasteners on the layout shown.
- A deep socket for the crossover tube clamps, a ratchet and extensions, and a hex bit that fits the supplied standpipe bracket bolt. A cordless ratchet can save time in spots where you have room to use it.
- A torque wrench that covers the specs in your kit instructions or Ram service information, plus hose-clamp pliers.
- A drain pan, a container for used coolant, the coolant specified for your Ram, clean shop towels, gloves, and safety glasses.
Preparation Steps
- Park on level ground. Set the parking brake and give the engine time to cool all the way down before you open the cooling system.
- Disconnect the batteries. Follow the Ram service procedure for your model year.
- Get the drain pan in place. Follow Ram’s coolant drain procedure before you undo a cooler hose. Leave the pan handy for any coolant still in the hoses or cooler.
6.7L Cummins EGR delete kit installation steps
Where the work is lawful, use this walkthrough when your kit and engine bay match the photos. Follow the instructions for your part number and use Ram service information for battery service, coolant handling, and factory fastener specs.
1. Take a few photos and clear some room
Take a few photos of the hoses, wiring, and brackets while everything is still in place. On the layout shown here, the plastic cover and dipstick bracket come out of the way first.
2. Take off the crossover tube and EGR valve
Follow the metal crossover tube to the valve by the intake. The PDF shows clamps at the ends and a center support bolt. Once the tube is out, unplug the valve and free the housing. Keep loose gasket material out of the intake. Set the intake plate and the seal shown for your kit in place, then check that the plate sits flat before you tighten it.
3. Work your way around the cooler
The manual shows the heat shields and front housing coming off before the front plate goes on. Follow the diagram for the clamp, factory nuts, and cooler mounts. Keep the drain pan under the cooler connections. Some coolant can stay in the cooler after the system drains.
The cooler still has a connection at the rear of the exhaust manifold. Support the cooler as you free it and keep it level when you lift it out. If the cradle still feels bolted down, look underneath. The PDF shows two bolts tucked out of sight. Once the cradle is out of the way, check that the rear plate and seal sit flat against the manifold.
4. Match the standpipe adapter, fitting, and hose to the photos
The kit shown here uses a standpipe adapter with its own bracket and a barbed fitting in place of the raised factory coolant fitting. Match the adapter and its seal to the picture, then check that the bracket sits in place without forcing the parts together. Follow the kit directions for the fitting sealant.
Lay the molded hose in place before you tighten the clamps. Both ends should slip all the way onto their fittings without a kink in the bend. Follow the hose with your eyes from end to end and make sure it has room around the exhaust and any sharp bracket edges. Reconnect the factory breather line as shown.
5. Refill the system and look for leaks
Return the shields, supports, and wiring clips called out in the instructions. Clear away any shop towels or temporary port covers as each opening is closed. Follow Ram’s fill and bleed procedure for your model year, then check the hose ends and fittings for drips.
If an initial run is lawful for your application, keep an eye on the temperature and shut the engine off if you see steam, an active leak, or a temperature warning. Wait until the engine is cold before opening the cooling system. Check the coolant level again and look for wet spots at the clamps or fresh soot around the plates.
What if something looks or sounds off?
- The same hose end keeps getting wet. Let the engine cool. Look at how far the hose sits on the fitting and where the clamp lands. If the level keeps dropping and the joints look dry, have the cooling system pressure-tested.
- The temperature climbs or the cab heater suddenly blows cold. Shut the engine off. Once it’s cold, look for a kinked hose and go back over the coolant fill and bleed procedure.
- You hear a new tick or see soot around a plate. Wait for the engine to cool and look where the plate meets the flange. A plate that sits crooked or a seal that shifted gives you a place to start.
- The check-engine light comes back. Save the code and note what the truck was doing when the light came on. Have the fault diagnosed before you drive or tow.
FAQ
Q1: Does the same EGR kit fit every 2010–2024 Ram pickup?
A1: Kits vary by model year and part number. Compare the plates, fittings, and hose in your box with the instructions for your kit.
Q2: Can I use these photos on a Ram 3500 dually?
A2: Start by looking up the factory build. If it’s a pickup and your kit matches the one pictured, use the guide for your model year. A factory 3500 Chassis Cab needs its own instructions.
Q3: Why does my kit have a different coolant hose?
A3: The manual pictured here shows one molded hose and a separate standpipe adapter. If yours has a different shape or uses other fittings, look up the diagram for the part number on your box.
Q4: Where are the cooler cradle bolts?
A4: On the layout shown in the PDF, two bolts sit underneath the cradle. See step 14 in the manual if you can’t spot them from above.
Q5: What if the coolant level keeps dropping after the truck cools?
A5: Look for fresh coolant around every connection you opened. If the level drops again and everything still looks dry, have the system pressure-tested before driving or towing.
Q6: Does off-road use make an EGR delete legal on my pickup?
A6: Federal emissions tampering rules still apply to EPA-certified pickups used only off-road or for racing.